Code:KAV20.1081MG
Brand:KAVAN
GO-1081MG (0.085s/60°, 45kg.cm)
Very high torque/high speed programmable digital standard brushless 83g servo with hardened steel gear and wide input voltage range 4.8-8.4V, 3xBB, ideal for large/giant aircraft, helis, 1:8-1:10 RC cars etc. Torque 28.0kg.cm, speed 0.140s/60° at 4.8V, torque 34.0kg.cm, speed 0.125s/60° at 6.0V, torque 39.0kg.cm, speed 0.110s/60° at 7.4V, torque 45.0kg.cm, speed 0.085s/60° at 8.4V. Aluminium case for perfect cooling under high load.
In Stock
Rotate with mouse
Very high torque/high speed programmable digital standard 83g brushless servo with hardened steel gear and triple BB-ed output shaft. Works great in large/giant planes, helicopters, 1:8 or 1:10 RC cars etc. All-aluminium case for perfect cooling under high load.
GO-1081MG is programmable using the KAVAN GO servo USB programmer/interface and PC software.
Programmable Functions
- Servo Angle: Maximal servo rotation angle range setting. The default range is ca 120° within the regular RC signal pulse width range (900~2100 µs); ca 180° within the max. signal pulse width range (500~2500 µs).
- Servo Neutral: Servo neutral (centre) position setting.
- Damping Factor: Servo damping setting – adjust the characteristics of the servo when stopping.
- PWM Power: Adjusts the servo output power. The higher the power, the higher the speed and torque of the servo – indeed also the current consumption will be higher.
- Sensitivity: Servo sensitivity (Dead Band) setting. The higher sensitivity the narrower the dead band – servo moves only if the change of the signal pulse width is bigger than the dead band width. Too high setting may cause servo jitter in some applications. Range: Ultra High (ca 1 µs dead band) – High (ca 2 µs) – Medium (ca 3 µs) – Low (ca 4 µs)
- Soft Start: Turns on/off the soft start feature. If ON, the servo goes slowly to the initial position corresponding to the servo signal once the power is switched on.
- Reverse: Reverses the servo movement direction.
- Narrow Band: FUTABA SR Mode – only for use with FUTABA radio channels working in the SR mode. Do not turn the option on if you are using a different setting of your FUTABA radio or any other radio.
- SANWA SSR: SANWA SSR Mode - only for use with SANWA radio channels working in the SSR mode. Do not turn the option on if you are using a different setting of your SANWA radio or any other radio.
- Lost PPM Protection (Fail-Safe): In the case the control signal from the receiver is lost completely or cannot be decoded correctly (due to interference) the servo can use choose one of three fail-safe modes:
- (a) Release: No fail-safe protection.
- (b) Keep Position: Keeps the position corresponding to the last correct control signal.
- (c) Go Neutral Position: The servo returns to the neutral (1500 µs pulse width) position.
- Over Load protection: Enables or disables overload protection of the servo in three levels – once the overload conditions last for the pre-set time (in seconds), the output power of the servo is reduced to the corresponding pre-set level (% of the max. power).
- Default: Restores the factory default setting of the connected servo.
Wide input voltage range 4.8-7.4 V (nominal).
25T/5.92 mm output shaft.
All GO servos are covered by an extended 3-year warranty.
| Servo dimensions | Standard |
| Servo type | Digital |
| Programmable | Yes |
| Thrust at 4.8V [kg/cm] | 28 |
| Thrust at 6.0V [kg/cm] | 34 |
| Thrust at 7.4V [kg/cm] | 39 |
| Thrust at 8.4V [kg/cm] | 45 |
| Speed at 4.8V [s/60st.] | 0.14 |
| Speed at 6.0V [s/60st.] | 0.115 |
| Speed at 7.4V [s/60st.] | 0.11 |
| Speed at 8.4V [s/60st.] | 0.085 |
| Servo gears | Metal |
| Ball bearings | 3× |
| High-voltage | Yes |
| Power supply [V] | 4.8 - 8.4 |
| Length [mm] | 40 |
| Width [mm] | 20 |
| Height [mm] | 37.2 |
| Weight [g] | 83 |
| Intended for | Aeroplanes,Helicopters,On-road cars,Off-road cars,Sailing boats,Boats |
